(647) 718-1514 Get a quote

What we wind

Six categories, all made to order

We do not hold a catalogue of pre-made parts. Every element is wound to the resistance, gauge and length your specific equipment needs, then measured against target before it ships.

±2%Resistance tolerance
48 hoursStandard lead time
Kanthal A1Wire we wind with
100%Wound in-house

Choose your equipment

Each page covers what fails, how to confirm it, and the brands we hold specifications for.

A potter loading bisque ware into an electric kiln in a studio

Kiln Elements

Studio potter, school or production ceramicist whose kiln is firing slow or stalling short of temperature.

Wire
Kanthal A1 (FeCrAl)
Voltage
120V / 208V / 240V
Tolerance
±2% resistance
See what we wind
An outdoor heat pump unit running beside a house in winter with snow on the ground

Heat Pump Elements

Trade or service customer replacing a supplementary heat element matched by resistance and frame.

Voltage
208V / 240V
Kit rating
5kW – 20kW
Control
Sequencer or contactor staged
See what we wind
An electric furnace air handler cabinet with its access panel removed

Furnace Elements

Trade or service customer needing an electric furnace element or heat strip matched to the original rating.

Voltage
208V / 240V
Kit rating
5kW – 25kW
Stages
1 – 5 sequenced
See what we wind
An electric water heater tank in a basement utility area with the element access panel visible

Water Heater Elements

Trade or maintenance customer replacing a water heater element to the original wattage and thread.

Voltage
120V / 240V
Wattage
1500W – 5500W
Mount
Screw-in (1" NPT) / Bolt-in (4-bolt flange)
See what we wind
An industrial process furnace on a plant floor

Industrial Furnace Coils

Plant maintenance or facility lead with a furnace down and a coil that has to match on spec, not badge.

Wire
Heavy gauge Kanthal A1 / APM
Voltage
208V / 240V / 480V / 600V
Phase
Single or three phase
See what we wind
A cleared residential driveway free of snow while surrounding ground is covered

Radiant & Snow Melt Cable

Builder or contractor specifying in-floor heat or heated-driveway cable to a measured run.

Use
Indoor floor / outdoor snow melt
Voltage
120V / 240V
Build
Insulated, cut to run length
See what we wind

Shop by kiln brand

Most kiln owners search by brand rather than by part. These are the makes we hold wind specifications for — model and serial still decide the exact set.

Skutt Paragon L&L Olympic Cone Art Evenheat Jen-Ken Cress Duncan
Use the kiln finder See every brand

Check your kiln's spec

We publish the wind specifications we hold, brand by brand, with element counts and voltages. Worth checking before you enquire — voltage matters as much as model, since the same kiln ships in both 208V and 240V and they take differently wound elements.

Open the kiln spec matrix Find elements for my kiln

How to order a custom coil

Three steps, and you do not need a part number for any of them.

  1. Send what you have

    Model and serial off the data plate, or a photo of the old element beside a tape measure. Either is enough to start.

  2. We confirm the spec

    We work out target resistance, wire gauge, coil length and termination style, then send it back in writing for you to check before anything is wound.

  3. We wind and measure

    Your set is wound in-house and every coil measured against target to ±2% before it ships. Standard lead time is 48 hours.

Get a quote

Not sure which category you need?

Send a photo of the equipment or the old element. We will tell you what it is and what it takes to replace it.

Send us a photo

Any one of these gets us started. A clear shot of the data plate is usually all we need.

From the data plate (optional if you sent a photo)
About the elements (optional)

A resistance reading off the old element verifies everything else. How to measure it

Delivery address (optional, for a shipping quote)

We reply within one business day. No obligation, no account needed.

Call (647) 718-1514